Tamko Fiberglass Slate Surface Roll Roofing Manual do Utilizador descarregar pdf

Application Instructions for

TAMKO

FIBERGLASS SLATE SURFACE

ROLL ROOFING

tamko.com

TAMKO

is a Registered Trademark

of TAMKO Building Products, Inc.

WHEN APPLIED ACCORDING TO THIS DIA-

GRAM, THE PRODUCT COVERS 98.76 SQUARE

FEET WITH A 3" TOP LAP AND A 4" END LAP.

This product is NOT to be used on slopes less than

2" per horizontal foot.

ROOF DECK – Roof deck must be smooth, dry and

free from warped surfaces. It is recommended that

metal drip edges be installed at eaves and rakes.

UNROLL BEFORE APPLYING – Rooﬁng should be

unrolled and allowed to lie ﬂat in warm sunlight for

some time in advance of application. This allows the

material to relax, thereby minimizing the possibility

of buckles and surface unevenness. THE SHEET

SHOULD BE CUT IN 12' to 18' LENGTHS.

TEMPERATURE – Rooﬁng must not be applied

when air temperature is below 50°F unless proper

pre cautions have been taken to allow for applica-

tion of the material.

ADHESIVE – TAMKO recommends TAMKO Cold

Method and Lap Cement and/or any cold applica-

tion cement meeting ASTM D 3019.

UNDERLAYMENT – TAMKO recommends the use

of underlayment with roll rooﬁng. Apply asphalt

saturated felt as underlayment over the entire deck.

Apply horizontally, parallel to eaves, lapping each

course of the felt over lower course at least 2" and

where ends join, lap the felt 4".

APPLICATION - Place 9" side strips of roll rooﬁng

along the eaves and rakes, positioning them to

overhang the deck 1/4" to 3/8". Fasten strips with

2 rows of nails as shown in diagram below. Posi-

tion a full-width strip of rooﬁng so that edges are

ﬂush with eaves and rakes. Fasten upper edge

with nails 4" on center and slightly staggered. Next

course should overlap nails a minimum of 1". Lift

lower edge of ﬁrst course and cover edge ﬁrmly into

cement. Continue each succeeding course in the

same manner, varying 12' to 18' sheet lengths, so

that end laps do not line up with one another. Pay

close attention to the laps because proper sealing

is critical.

WARNING

All cement is to be applied in thin, smooth, even

layers. Excessive use of cement will cause blister-

ing of this prod uct. All nails should be covered. If

any nails remain exposed, cover them with plastic

asphalt rooﬁng cement.

Additional illustrations and installation details are

available in the Asphalt Rooﬁng Manufacturers

Association Booklet, “Residential Asphalt Rooﬁng

Manual”.

Roll rooﬁng may also be applied vertically, parallel

to the rakes.

FIBERGLASS SLATE SURFACE 1

Resumo do Conteúdo

Página 1 - FIBERGLASS SLATE SURFACE

Application Instructions forTAMKO® FIBERGLASS SLATE SURFACEROLL ROOFING tamko.comTAMKO® is a Registered Trademark of TAMKO Building Products,

Comentários a estes Manuais

Sem comentários

Tamko Fiberglass Slate Surface Roll Roofing Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Para a casa Tamko Fiberglass Slate Surface Roll Roofing. TAMKO Fiberglass Slate Surface Roll Roofing User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Para a casa Tamko Fiberglass Slate Surface Roll Roofing